VR3 2 PIN drager port - Major F*~k up?

Deepthought_reloaded · 9th December 2006, 12:00

Hi,

Just got a brand new p-port drager interface for my 7-pin VR3

It's only got 2 pins?

Have Delta-P stuffed up and sent me an old one or do they not fit the 5 unused pins?

IIRC there was a comment about the center pin being used if you wired your own connector, this certainly is not there - the two pins look like they are at the 12oclock and 6 oclock with the red dot at the top and I dont think there would be room between then for another pin.

The Pins themselves look a little too fat?

Comments please

jar_uk1 · 9th December 2006, 13:00

Quote: (Originally Posted by Deepthought_reloaded)

Hi,

Just got a brand new p-port drager interface for my 7-pin VR3

It's only got 2 pins?

Have Delta-P stuffed up and sent me an old one or do they not fit the 5 unused pins?

IIRC there was a comment about the center pin being used if you wired your own connector, this certainly is not there - the two pins look like they are at the 12oclock and 6 oclock with the red dot at the top and I dont think there would be room between then for another pin.

The Pins themselves look a little too fat?

Comments please

I am not sure if it helps, but I just checked my dragers VR3 P port interface and it has all 7 pins in place (center pin with 6 evenly spaced pins around it).

John R

Barrie Law · 9th December 2006, 14:01

Quote: (Originally Posted by Deepthought_reloaded)

Hi,

Just got a brand new p-port drager interface for my 7-pin VR3

It's only got 2 pins?

Have Delta-P stuffed up and sent me an old one or do they not fit the 5 unused pins?

IIRC there was a comment about the center pin being used if you wired your own connector, this certainly is not there - the two pins look like they are at the 12oclock and 6 oclock with the red dot at the top and I dont think there would be room between then for another pin.

The Pins themselves look a little too fat?

Comments please

You have been sent the Older 2 pin connector type.

Give them a bell on Monday and sort it out.

Regards

abowie · 9th December 2006, 20:38

http://www.rebreatherworld.com/kiss-...cher#post25656

Should look like this.

9th December 2006, 12:00	#1 (permalink)
Deepthought_reloaded New Member Current Rebreather/s: Azimuth Other Rebreather/s: Azimuth Join Date: Oct 2006 Location: York Posts: 59	*VR3 2 PIN drager port - Major F~k up?** Hi, Just got a brand new p-port drager interface for my 7-pin VR3 It's only got 2 pins? Have Delta-P stuffed up and sent me an old one or do they not fit the 5 unused pins? IIRC there was a comment about the center pin being used if you wired your own connector, this certainly is not there - the two pins look like they are at the 12oclock and 6 oclock with the red dot at the top and I dont think there would be room between then for another pin. The Pins themselves look a little too fat? Comments please
(Offline)

9th December 2006, 13:00	#2 (permalink)
jar_uk1 New Member Current Rebreather/s: Inspiration Vision Dolphin Other Rebreather/s: Dolphin Join Date: Dec 2005 Location: Bracknell, UK Posts: 66	*Re: VR3 2 PIN drager port - Major F~k up? Quote: (Originally Posted by Deepthought_reloaded**) Hi, Just got a brand new p-port drager interface for my 7-pin VR3 It's only got 2 pins? Have Delta-P stuffed up and sent me an old one or do they not fit the 5 unused pins? IIRC there was a comment about the center pin being used if you wired your own connector, this certainly is not there - the two pins look like they are at the 12oclock and 6 oclock with the red dot at the top and I dont think there would be room between then for another pin. The Pins themselves look a little too fat? Comments please I am not sure if it helps, but I just checked my dragers VR3 P port interface and it has all 7 pins in place (center pin with 6 evenly spaced pins around it). John R
(Offline)

9th December 2006, 14:01	#3 (permalink)
Barrie Law RebreatherWorld Sponsor Current Rebreather/s: Inspiration Classic Other Rebreather/s: Join Date: Jun 2005 Location: Ireland Posts: 726	*Re: VR3 2 PIN drager port - Major F~k up? Quote: (Originally Posted by Deepthought_reloaded**) Hi, Just got a brand new p-port drager interface for my 7-pin VR3 It's only got 2 pins? Have Delta-P stuffed up and sent me an old one or do they not fit the 5 unused pins? IIRC there was a comment about the center pin being used if you wired your own connector, this certainly is not there - the two pins look like they are at the 12oclock and 6 oclock with the red dot at the top and I dont think there would be room between then for another pin. The Pins themselves look a little too fat? Comments please You have been sent the Older 2 pin connector type. Give them a bell on Monday and sort it out. Regards __________________ Barrie Law Rebreather World Store Supplying the Rebreather World Tel:US +19548403892 Fax:US+19543333792 Tel:EU+442071930496 Fax:EU+442077606344 Mobile+353876880628 Skype:barrielaw Email: barrie@rebreatherworldstore.com
(Offline)

9th December 2006, 20:38	#4 (permalink)
abowie Fighting Girl Current Rebreather/s: Sport Kiss Other Rebreather/s: Join Date: May 2005 Location: Land of Oz Posts: 573	*Re: VR3 2 PIN drager port - Major F~k up?** http://www.rebreatherworld.com/kiss-...cher#post25656 Should look like this. __________________ Andrew Bowie Rebreather-friendly Buddy
(Offline)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode