+ Post New Thread
Page 1 of 96 1 2 3 4 5 6 7 8 11 51 ... LastLast
Threads 1 to 20 of 1912

Forum: Inspiration / Evolution Rebreathers

Questions, answers and discussion regarding the Inspiration Rebreather & Evolution Rebreather.

  1. Sticky Thread Sticky: alibox special deals

    hi all the last batch of aliboxes sold very well , normally this was to be the last for a while as i have been concentrating on the camelion...

    Started by michael hearn‎, 27th October 2010 16:47
    14 Pages
    1 2 3 4 5 ... 14
    • Replies: 138
    • Views: 44,506
    12th March 2013, 13:50 Go to last post
  2. Question Sticky Thread Sticky: Removing hose fittings

    I'm trying to open the hose fittings on either end of my inhale hose to replace it. I have a hose tool from Narked at 90 to hold the inner fitting,...

    Started by Mick F‎, 8th May 2006 18:05
    5 Pages
    1 2 3 4 5
    • Replies: 46
    • Views: 22,094
    5th August 2009, 14:37 Go to last post
  3. Sticky Thread Sticky: Vision HUD simulator

    Been at home with serious 'man flu' this week, so thought I'd try and create an interactive version of the instructor flash cards for learning the...

    Started by rewrites‎, 19th December 2008 17:52
    4 Pages
    1 2 3 4
    • Replies: 34
    • Views: 14,541
    5th March 2009, 13:58 Go to last post
  1. G Box cylinder mount mod

    I read in a post a while back of someone placing a plastic channel sleeve to slide over the cylinder bracket to keep the cylinder from sliding so...

    Started by monkfe‎, 16th October 2018 20:20
    • Replies: 1
    • Views: 164
    17th October 2018, 18:20 Go to last post
  2. Vision in Evolution case

    Does anyone have pictures of a vision scrubber in the small (47.5cm) Evo case? I've seen it in the 51cm Evo+ Case but not the dinky one. Can the...

    Started by deepdave‎, 14th October 2018 21:04
    • Replies: 5
    • Views: 230
    15th October 2018, 19:40 Go to last post
  3. Looking for a Temp Stick for AP Inspiration vision

    Hi, anybody a spear Temp Stick for sale? my Temp is broken.

    Started by Kurt9900024‎, 7th August 2018 12:32
    • Replies: 0
    • Views: 474
    7th August 2018, 12:32 Go to last post
  4. AP classic handsets

    So I pulled the rubber covers to check the handsets. All working fine with LED’s and doesn’t leak. Passes positive and negative. But I’ve found some...

    Started by Figjam007‎, 7th August 2018 12:09
    • Replies: 0
    • Views: 473
    7th August 2018, 12:09 Go to last post
  5. CL mods

    Hi there! I've read somewhere else that it's possible to modify the inspo front lungs into back mounted ones. Is it really possible? How it's...

    Started by evandroairton‎, 28th July 2018 18:48
    • Replies: 2
    • Views: 552
    30th July 2018, 00:42 Go to last post
  6. G-Box vs Custom Diver frame

    Hi, I'm just getting ready to take my unit abroad for the first time (Malta), I currently have the original setup and although I don't have enough...

    Started by Simon-inspo‎, 15th April 2018 16:40
    • Replies: 7
    • Views: 1,229
    23rd July 2018, 19:41 Go to last post
  7. APD BMCLs - OPV placement

    Hi, anybody else here having problems to reach the OPV cord to dump gas during OC bailout? While it´s "doable" in a "normal situation "it´s in...

    Started by com1‎, 1st July 2018 16:27
    • Replies: 5
    • Views: 488
    2nd July 2018, 20:06 Go to last post
  8. Shipping & Custom Cost

    What would the shipping and custom cost for a Evolution to be shipped to the UK from the US ??????? Cheers

    Started by taza‎, 15th August 2007 22:53
    • Replies: 7
    • Views: 6,295
    17th May 2018, 16:33 Go to last post
  9. CO2 Sensor bleeps on a 2020 head

    Hi, last year I installed a CO2 sensor into the head of my 2020 inspo. It works really well and certainly adds a nice reassurance factor on dives. ...

    Started by Simon-inspo‎, 16th March 2018 23:06
    • Replies: 8
    • Views: 1,457
    15th April 2018, 16:30 Go to last post
  10. Oxidation on smb connectors

    Hi. Sorry if this has been discussed earlier. Could not find any thread talking about this in detail. I am starting to develop some oxidation around...

    Started by sluca‎, 13th July 2016 13:52
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 53
    • Views: 10,140
    14th April 2018, 18:20 Go to last post
  11. Update on AP Diving CO2 sensor

    Hi, the last comments on the APD CO2 sensor are quite old. Is there any update? Reliability? It seems that with the last firmware and a good...

    Started by gzaccaria‎, 6th April 2018 06:48
    • Replies: 6
    • Views: 901
    9th April 2018, 14:27 Go to last post
  12. 2020 hand set keeps switching on when dry?

    Hi all, My 2020 handset keeps switching on automatically, this is with the handset dry in a warm room. I wonder if it is because it hasn't been...

    Started by GregPartridge‎, 13th March 2018 19:47
    • Replies: 4
    • Views: 1,082
    30th March 2018, 22:07 Go to last post
  13. Solenoid MK3 not firing issues

    Hi, has anybody had any problems with their solenoid MK3 unit? A few times the unit won't do the "clicking" check noise and just today I tested the...

    Started by RoyJN‎, 22nd March 2018 06:29
    • Replies: 5
    • Views: 833
    30th March 2018, 02:51 Go to last post
  14. Hollis BOV on Inspo?

    I thought I read somewhere that the Hollis BOV can be used on the Inspo, but can't find that post again. Does anyone have any insight? Is it a whole...

    Started by moose_grunt‎, 21st May 2015 12:03
    6 Pages
    1 2 3 4 5 ... 6
    • Replies: 54
    • Views: 18,512
    20th March 2018, 00:16 Go to last post
  15. Battery usage question

    Hi, I have a question about battery usage. I bought a Vision (2012, with CR123 + MK3 solenoid) from a friend and followed the Mod 1 course. I'm...

    Started by Arjantange‎, 1st August 2017 08:57
    2 Pages
    1 2
    • Replies: 15
    • Views: 3,960
    6th February 2018, 00:46 Go to last post
  16. SPG hose leak

    The ap hp hoses has a swivel in the threaded end. Right? Cool for mounting with the hose routed along the lungs. However, both my hoses leaks...

    Started by DennisA‎, 21st December 2017 05:42
    • Replies: 7
    • Views: 3,492
    12th January 2018, 09:56 Go to last post
  17. Lightbulb One Piece Harness with AP BMCLs

    Hi all, New to RBW, tried looking for an answer but unsuccessful so far. Sorry if there is, please just post a link if so. Started CCR diving...

    Started by Dabbskebabs‎, 15th December 2017 10:16
    2 Pages
    1 2
    • Replies: 12
    • Views: 5,059
    12th January 2018, 03:31 Go to last post
  18. Question Inspiration Classic Threads?

    Hi RBW folks, I convert my Inspiration to mCCR. I decidet to make a new Head an a new sensor holder. Can someone tell me what threads are used...

    Started by Sascha H‎, 1st January 2018 17:06
    inspirationclassic, kissstyle, mccr, thread
    • Replies: 2
    • Views: 2,825
    3rd January 2018, 14:18 Go to last post
  19. MCCR Inspo

    Hi everybody! I would like to make an mccr spare head, to use if i have issues with the electronics. So, i would like to know about any...

    Started by evandroairton‎, 22nd December 2017 18:46
    • Replies: 0
    • Views: 1,973
    22nd December 2017, 18:46 Go to last post
  20. temp stick or CO2 sensor

    Hi, on my 2010 unit the temp stick started to go on/off during the dive (probably broken wires where it enters the stick), as I understood this is...

    Started by com1‎, 28th October 2017 13:07
    2 Pages
    1 2
    • Replies: 10
    • Views: 2,413
    8th November 2017, 17:12 Go to last post

+ Post New Thread
Page 1 of 96 1 2 3 4 5 6 7 8 11 51 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 50 replies or 1000 views
Hot thread with unread posts
More than 50 replies or 1000 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts