+ Post New Thread
Page 1 of 3 1 2 3 LastLast
Threads 1 to 20 of 47

Forum: Hollis

  1. BOV hard to close ?

    Since my unit has been new, the bov has been difficult to close. Like two handed difficult to close. I have pulled it apart multiple times, cleaned,...

    Started by A878bob‎, 2nd December 2017 17:35
    • Replies: 7
    • Views: 579
    5th December 2017, 15:42 Go to last post
  2. 4 Red Lights HUD

    Evening guys, I have a Prism2 and the HUD is constantly displaying a Red LED in each corner of the HUD and blinking constantly. The Hud...

    Started by LiamCCR‎, 27th November 2017 21:56
    • Replies: 2
    • Views: 758
    30th November 2017, 18:45 Go to last post
  3. Sub Gravity BMCL's

    Ran across a post where someone said they were diving these but didn't get any information other than a link. I love/hate the Prism and most of my...

    Started by dauntless_divers‎, 11th November 2017 11:32
    • Replies: 9
    • Views: 969
    26th November 2017, 16:43 Go to last post
  4. Dmea 2017

    Anybody know if there are updates to the Prism 2 being released or previewed at DEMA this year? Thanks!

    Started by Nix‎, 1st November 2017 21:27
    • Replies: 2
    • Views: 538
    2nd November 2017, 15:57 Go to last post
  5. Prism 2 BMCL?

    We were told they would release in the early 2017 wich they postponed, and said more information coming. Later on they've promised that they will...

    Started by Meivi‎, 12th September 2017 10:39
    • Replies: 4
    • Views: 955
    25th October 2017, 00:35 Go to last post
  6. Prism 2: Cracked Scrubber Cannister Lid

    Hi, I managed to crack the lid on my Prism 2's scrubber cannister this weekend... long story. I have a spare cannister & lid, but since I've...

    Started by maxguru‎, 16th October 2017 16:57
    • Replies: 1
    • Views: 431
    17th October 2017, 01:57 Go to last post
  7. Hollis Discontinuing Rebreathers?

    I heard a rumor today from a distributor that Hollis will be discontinuing the Prism following their buyout. Can anyone confirm this? Cheers,...

    Started by dauntless_divers‎, 13th June 2017 13:19
    3 Pages
    1 2 3
    • Replies: 24
    • Views: 5,721
    7th October 2017, 00:36 Go to last post
  8. D-rings or UCL for bailouts?

    I have been running under counter lung offset rings on my harness to run my bailout, now rigging for 2 al80's, the weight of the 80's, even in the...

    Started by A878bob‎, 3rd September 2017 22:37
    • Replies: 1
    • Views: 721
    4th September 2017, 00:58 Go to last post
  9. New sensor reading 14.7 mV in air. Would you dive it?

    I unwrapped a new sensor Saturday morning, installed it in my unit and it read 14.7 mV in air. The spec in the checklist is 8.5 - 14 mV in air. I...

    Started by maxguru‎, 28th August 2017 18:26
    2 Pages
    1 2
    • Replies: 11
    • Views: 1,231
    31st August 2017, 09:59 Go to last post
  10. Europe Service

    Hi, where I can find a reliable service center for prism 2 In Europe? have someone an email address? Thank you.

    Started by lorescuba‎, 26th July 2017 11:21
    • Replies: 0
    • Views: 653
    26th July 2017, 11:21 Go to last post
  11. Pre-dive asambly check list

    Hi By some Strange reason my dive burde insist that have used the wrong pre-dive asambly check liste!!!! :cheers: :sarcy:

    Started by Olsen DK‎, 3rd July 2017 18:07
    • Replies: 4
    • Views: 1,129
    7th July 2017, 06:36 Go to last post
  12. Prism2 CE approved

    Hey Has anyone any news regarding the CE approval of the Prism2 rebreather? At Hollis web page there are a small line at the bottom of the Prism2...

    Started by Olsen DK‎, 20th January 2015 20:10
    2 Pages
    1 2
    • Replies: 11
    • Views: 6,078
    3rd July 2017, 19:04 Go to last post
  13. Cool Prism trim weighting ?

    I have been diving my prism for about 6 months and still trying to dial in the weighting for trim. I have been moving more of the weight down low...

    Started by A878bob‎, 19th June 2017 00:09
    • Replies: 8
    • Views: 1,139
    24th June 2017, 23:01 Go to last post
  14. P2 cylinder fit question

    I have a p2 and I normally dive it with 30CF Luxfer AL tanks. I recently received a pair of Faber FX27 steel tanks. Because the steel tanks...

    Started by shortkidd‎, 26th February 2017 22:17
    2 Pages
    1 2
    • Replies: 11
    • Views: 2,532
    21st April 2017, 23:59 Go to last post
  15. New Hollis Prism 2 BMCL & More at DEMA 2014

    Hollis will have at their DEMA booth a Back mounted counter lungs for the Hollis Prism 2. The new lung will be shipping January 2015. Unit with...

    Started by Chett.L‎, 11th November 2014 23:44
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 9,007
    25th March 2017, 06:58 Go to last post
  16. Oeticker Pliers?

    Anyone know where I can get a pair to remove the clamps on the breathing hoses of my P2? I think Add Helium used to have them listed on their...

    Started by maxguru‎, 20th December 2016 16:46
    2 Pages
    1 2
    • Replies: 13
    • Views: 3,987
    23rd March 2017, 04:15 Go to last post
  17. Prizm 2 HUD problem

    Hi everyone, I am trying to investigate a problem with the HUD of the Prizm, would love to know if someone else are experiencing the same thing or...

    Started by UdiFreeze‎, 18th March 2017 18:37
    • Replies: 1
    • Views: 1,618
    19th March 2017, 06:37 Go to last post
  18. Does anyone add weight in their Counterlungs

    Not sure if all the other brands have built in weight pockets, but the Hollis Prism 2 has weight pockets in both counterlungs. I have never used...

    Started by Chett.L‎, 1st September 2016 01:50
    4 Pages
    1 2 3 4
    • Replies: 35
    • Views: 4,564
    17th March 2017, 15:49 Go to last post
  19. 2x PRISM 2 tips needed

    Hi RBW members I need two good tips for the Prism 2 unit: 1: What is the best way to remove the crushed/stock sorb on the radial scrubber?...

    Started by depth‎, 11th March 2017 19:00
    • Replies: 7
    • Views: 1,027
    15th March 2017, 18:35 Go to last post
  20. P2 divers, what do you store your scrubber basket in?

    I'm getting tired of "double bagging" my scrubber basket in Ziploc bags when I take it out of my unit with time remaining on the scrubber material. ...

    Started by maxguru‎, 8th September 2016 16:39
    2 Pages
    1 2
    • Replies: 12
    • Views: 2,407
    11th January 2017, 11:46 Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 50 replies or 1000 views
Hot thread with unread posts
More than 50 replies or 1000 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts